Protherm leopard manual

Exhaust gas will not enter the air. Specially mounted pipe for its withdrawal is not needed, rather horizontal, mounted in the wall. Through it air from the street will be taken. It is important to remember that water condensate in the cold season can lead to the formation of icicles on the pipe. Condensing boiler has the same properties as the fan.

The price is the biggest drawback of such a model, because it is high. Condensate remains in the water drainage system, icicles are not formed. Plus - the gas consumption is much less, which saves money on fuel. Every consumer who wants to install a gas heating device at home or in another building or structure makes a choice based on his requirements, financial possibilities and, of course, the characteristics of the room that he plans to heat.

As for the model range and as we remember, there are seven lines of Protherm , then in this section we will focus on the most popular consumer types. This view is ideal for buildings with an area not exceeding m2, that is, for villas, country cottages.

Jaguar not only heats, but also provides hot water. It has two separate heat exchangers. Fuel for it is the main gas, its consumption is relatively small - from 2.

One of its heat exchanger is made of copper, the other is made of stainless steel. Included with it is a circulation pump. Users rate this model extremely positively because of the convenience and ease of installation and operation. No less popular "Panther" - another wall model. The strength of its hydraulic unit is enhanced by the composite materials from which it is made.

The design of the product has a pump and tank, as well as a special option "Comfort". Thanks to her, the water heats up in just 5 seconds. This model does not require the presence of a chimney, the products of combustion go through the coaxial system. Another option from the model range - "Lynx". She also has two separate heat exchangers with the ability to separately adjust the temperature level in each.

Since this model is two-circuit, it has a circulating pump and an expansion tank, the volume of which is 7 liters. The most controversial reviews from consumers are received on the Leopard model. This product also applies to the wall ruler. To adjust the "Leopard" has one automatic window. Users note that at an outdoor temperature of and below the boiler heats the room slightly.

In addition, at low street temperatures, the product overheats, and during long frosts below 40 degrees, the heat sensor often fails and must be replaced. Medved operates on two types of fuel - both main gas and liquefied gas are suitable for it. The model is non-volatile, works without connection to the electrical network.

The Grizzly model is more powerful and at the same time simple. It can be used to heat large rooms of up to 15 thousand m2. Even during unstable power supply, it provides uninterrupted heating of the room. Designed for heating only, has one circuit. Also non-volatile. Develops power up to 45 kW. It is possible to replace the sections and complete them, based on the needs of the consumer.

To connect the boiler to the electrical network of a private house, it is necessary to intervene in its internal structure. This type of work is carried out only by Protherm certified personnel.

If you decide to do it yourself, you need to remember that after that, most likely, you will not be able to service the boiler and eliminate interruptions in its work under warranty.

The degree of warmth and comfort in the house depends on how high-quality materials are selected and how skillfully the installation is carried out. If you choose the correct boiler strapping scheme, the system will be protected from overheating, overload, and all the rooms in the house will be heated evenly.

Arranging the strapping scheme, you need to be guided by the building regulatory documentation. Strapping is the whole heating system minus batteries radiators. The system includes a large number of nodes and devices, but even the amateur can install the simplest strapping scheme.

The boiler is set up on the LCD display, and adjustment is also performed there. Before starting installation works of the room regulator, the boiler is disconnected from electricity - this is a prerequisite. Each boiler has a tubular fuse, it can be seen on the control panel. If the regulator has a relay switch, then the maximum load on it should not exceed 24 watts. The regulator is connected to the boiler using a two-wire cable.

Copper wire having a cross section of 1. Table Of Contents. Quick Links. Table of Contents. Previous Page. Next Page. Floorstanding cast iron boiler cascade conection possible output up to kw grizzly 21 pages. The "Installation " Only turned on boiler has activated all protective function e.

The lights continuously. Page 8 Operation diagram Warning: The protective functions are only active if the boiler is plugged into the Safety valve electrical grid socket and the main switch The boiler is equipped with a safety valve. Puterea poate fi setat majorat sau redus n funcie de necesitate conform tabelului menionat mai jos, pe display este afiat puterea nainte de virgula decimal de ex.

Cazanul are ncorporat funcia de protecie mpotriva ngheului, care protejeaz cazanul nu ns sistemul de nclzire i conductele de distribuie ACM mpotriva ngheului. La scderea temperaturii apei de nclzire sub 8 C pompa va porni indiferent de solicitarea regulatorului de camer sau fr a ine cont de setarea regimului de var.

Dac temperatura apei de nclzire din cazan crete i ajunge la 10 C, pompa se oprete automat. Dac temperatura apei de nclzire scade din nou, la atingerea temperaturii sub valoarea de 3 C cazanul va fi blocat. Dac temperatura n alimentatorul ACM scade la valoarea de 5 C, cazanul va nclzi apa n alimentator la valoarea de 8 C. Not: Aceast funcie este activ doar la conectarea alimentatorului extern, care este echipat cu senzorul NTC.

Prin scurta pornire a pompei aprox. Not: Aceast funcie a cazanului nu poate fi blocat. La nclzirea ACM n alimentatorul extern durata de funcionare a pompei dup decuplare este setat la 1 minut.

La nclzirea apei de nclzire durata de funcionare a pompei dup decuplare este setat la 10 min. Durata de funcionare a pompei dup decuplare poate fi schimbat, n caz de nevoie, de ctre tehnicianul de service autorizat. Not: Aceast funcie este activ doar la conectarea cazanului la reeaua electric i la pornirea ntreruptorului principal.